SPECIALS FOR SALE

Click on small images for larger image

 

All prices plus shipping and tax (if applicable)

 

 

 

 

 

1. Brand new Quantum Life Conditioner boards: These are the actual circuit boards used in the Quantum conditioner products. We bought some of the boards to put into machines to mod but have decided the boards are too large to put into the machines that we mod. We have the following:

 

6 Quantum boards 1.5" X 1.75" boards that are the Electroclear products. These boards work directly off 120V and can be installed right inside of equipment. Great inside power conditioners and equipment. $25.00 each.

 

 

 

2. One Audiocom Superclock I 11.2866 Mhz clock module. $100.00. Works in Sony C555 and XA777ES as well as some other machines.

 

 

 

3. Custom pair of speakers:

 

One pair of custom speakers for sale. Unfinished (unpainted highly refined particle board--like Rangerboard). The speakers consist of:

 

2 Scanspeak 8545 woofers per channel in cabinet (24"x16"x12"). Each 8545 is in its own separate 19 liter enclosure. There is a port hole on the back for each woofer (I use one with port and one woofer closed box, you can use however you choose). The box is made with two different thicknesses of highly refined particle board with visco elastic bonding material (Swedac) in between. All cabinet walls and braces are one and one quarter inch thick. The Scanspeak drivers have Marigo dots on them and Deflex on the back of the magnets. The drivers are mounted to the cabinet with deflex gasket material. The insides of the boxes have some deflex and some long hair wool. Will sell woofers separately.

 

The midranges are two Vifa 5 inch drivers (P 13WG-00-05) mounted on an open baffle (15 inches high by 12 inches wide--same width as woofers). This vertical baffle is attached to a panel that sits on top of the entire top of the woofer. The two pieces are braced together by two heavy steel shelf brackets that are damped with Soundcoat GP-3 damping material. Both the front baffle and flat bottom panel are one and one half inches thick (two three quarter inch pieces of highly refined particle board with Swedac in between). The midrange drivers have Marigo dots on them and Deflex material on the back of their magnets.

 

The tweeter is a modified Vifa (D27TG-45). It has the back cut off to lower its resonance frequency and lower distortion. This tweeter was A/Bed with an Esotar and found to sound the same (at least with the 95db level we were listening to). Before modding the Vifa sounded distorted by comparison. The tweeter is mounted from the back on a three quarter inch thick piece of highly refined particle board (six inches high by 12 inches wide) that sits on top of the midrange panel (currently connected by cellophane tape). Of course, you would do a more secure mounting. The tweeter fires through a flared opening in the panel and is slightly set back on the midrange panel to time align it with the midranges (this is why it is mounted from the rear of the panel, as well).

 

The crossover is a 3 mh 12 gauge air coil from Northcreek on the woofer, nothing on the midranges (running wide open) and 8 uf of Infinicap with .01 uf Infinicap bypasses on the tweeter. The crossover frequencys are 300 cycles and about 5 K. The midrange drivers on the open baffle start to fall at 300 cycles by themselves.

 

Speakers are 90.5db sensitive and 4 ohm.

 

There are adjustable spikes on the bottom of the woofers. Wires on the woofers are some Audioquest solid core and the wires from the midranges to the tweeter are very little insulated pieces of Harmonic Tech top of the line speaker wire. No other wire or binding posts (yuck, please hard wire) are supplied. I used them biwired with some custom wires, wired directly from the output devices on my amps to the midranges and then jumpers to the tweeters along with separate woofer wires to the coils for the woofers.

 

 

$525 for all of the above......pick-up only, unless just buying woofer...these I can ship.

WILL consider selling the woofers separately, $150 pair or $280 for four.

 

 

The woofer boxes and panels cost me $600 to have made. The retail on the woofers is about $600. The midrange drivers are about $70 and the tweeters about $50. The Infinicaps, giant Northcreek coils, Deflex, spikes, Navcom, brackets, etc. well.......anyway, its a bargain.....to say the least.

 

These speakers weigh about 100 lbs. each. Over 70 lbs. for the woofer box and about 30 lbs. for the top panel.

 

The total dimensions are 46 inches high, 12 inches wide and 16 inches deep.

 

With a good paint job and some nice felting on the face of the midrange/tweeter panel these speakers will look quite professional. The cabinets were made by an artist/woodworker in Berkeley, CA and have rounded edges and are made very well.

 

Most importantly they sound great! Very open and electrostatic like.

 

 

 

 

 

 

 

4. Parts and other stuff.

 

6 24.704mhz Raltron VCXOs (great for use with CS8420). $20.00 @

 

11 Signal Transformer power transformers: DP-241-6-28 (split bobbin, dual primary/120-240V, 30 watt, 28VCT).

$7.00 @

 

9 used transformers.....same as above (241-6-28) but single primary (120 volt only) $3.00@

 

2 used Toroid of America toroidal transformers... all are 117V input:

one has 2 15 V secondaries at 5.9A (180 watt) $15.00

one has 2 15 V secondaries at 4.0 amps (120 watt) $10.00

Both have short wires and no hardware.

 

 

All parts brand new except where noted. Most below wholesale, some downright giveaways. $25.00 minimum order for sales within U.S. shipped by UPS. We do not ship parts by mail within the U.

 

 

 

$50.00 minimum order for Overseas orders. Minimum order amount based on the fact that I have to go to the post office (45 minutes), fill out customs slip, etc. Remember, I am selling these parts at less than what I paid!

 

 

 

 

 

All prices plus shipping and tax (if applicable).

 

 

   What's New      EVS products